deepseek Bot
324d114386
- Add platformio.ini for ESP32 DevKit (Arduino framework, espressif32 6.10.0) - Vendor ArduinoJson, MPU6050_tockn, SCServo, Simple_FOC, and WebSockets so a fresh clone builds without downloading dependencies - Add .gitignore rules for PlatformIO/IDE build artifacts - Add controller PCB Gerber and drill files
123 lines
2.9 KiB
Arduino
123 lines
2.9 KiB
Arduino
/*
|
||
回读所有舵机反馈参数:位置、速度、负载、电压、温度、移动状态；
|
||
FeedBack函数回读舵机参数于缓冲区，Readxxx(-1)函数返回缓冲区中相应的舵机状态；
|
||
函数Readxxx(ID)，ID=-1返回FeedBack缓冲区参数；ID>=0，通过读指令直接返回指定ID舵机状态,
|
||
无需调用FeedBack函数。
|
||
Read back all feedback parameters: position, speed, load, voltage, temperature, movement status;
|
||
The FeedBack function reads back the servo parameters in the buffer, and the Readxxx (-1) function returns the corresponding servo state in the buffer;
|
||
Function Readxxx (ID), ID=1 returns the FeedBack buffer parameter; ID > 0, and directly returns the specified ID rudder state by reading the instruction.
|
||
There is no need to call the FeedBack function.
|
||
*/
|
||
|
||
// the uart used to control servos.
|
||
// GPIO 18 - S_RXD, GPIO 19 - S_TXD, as default.
|
||
#define S_RXD 18
|
||
#define S_TXD 19
|
||
|
||
#include <SCServo.h>
|
||
|
||
SCSCL sc;
|
||
|
||
void setup()
|
||
{
|
||
Serial1.begin(1000000, SERIAL_8N1, S_RXD, S_TXD);
|
||
Serial.begin(115200);
|
||
sc.pSerial = &Serial1;
|
||
delay(1000);
|
||
}
|
||
|
||
void loop()
|
||
{
|
||
int Pos;
|
||
int Speed;
|
||
int Load;
|
||
int Voltage;
|
||
int Temper;
|
||
int Move;
|
||
if(sc.FeedBack(1)!=-1){
|
||
Pos = sc.ReadPos(-1);
|
||
Speed = sc.ReadSpeed(-1);
|
||
Load = sc.ReadLoad(-1);
|
||
Voltage = sc.ReadVoltage(-1);
|
||
Temper = sc.ReadTemper(-1);
|
||
Move = sc.ReadMove(-1);
|
||
Serial.print("Position:");
|
||
Serial.println(Pos);
|
||
Serial.print("Speed:");
|
||
Serial.println(Speed);
|
||
Serial.print("Load:");
|
||
Serial.println(Load);
|
||
Serial.print("Voltage:");
|
||
Serial.println(Voltage);
|
||
Serial.print("Temper:");
|
||
Serial.println(Temper);
|
||
Serial.print("Move:");
|
||
Serial.println(Move);
|
||
delay(10);
|
||
}else{
|
||
Serial.println("FeedBack err");
|
||
delay(500);
|
||
}
|
||
|
||
Pos = sc.ReadPos(1);
|
||
if(Pos!=-1){
|
||
Serial.print("Servo position:");
|
||
Serial.println(Pos, DEC);
|
||
delay(10);
|
||
}else{
|
||
Serial.println("read position err");
|
||
delay(500);
|
||
}
|
||
|
||
Voltage = sc.ReadVoltage(1);
|
||
if(Voltage!=-1){
|
||
Serial.print("Servo Voltage:");
|
||
Serial.println(Voltage, DEC);
|
||
delay(10);
|
||
}else{
|
||
Serial.println("read Voltage err");
|
||
delay(500);
|
||
}
|
||
|
||
Temper = sc.ReadTemper(1);
|
||
if(Temper!=-1){
|
||
Serial.print("Servo temperature:");
|
||
Serial.println(Temper, DEC);
|
||
delay(10);
|
||
}else{
|
||
Serial.println("read temperature err");
|
||
delay(500);
|
||
}
|
||
|
||
Speed = sc.ReadSpeed(1);
|
||
if(Speed!=-1){
|
||
Serial.print("Servo Speed:");
|
||
Serial.println(Speed, DEC);
|
||
delay(10);
|
||
}else{
|
||
Serial.println("read Speed err");
|
||
delay(500);
|
||
}
|
||
|
||
Load = sc.ReadLoad(1);
|
||
if(Load!=-1){
|
||
Serial.print("Servo Load:");
|
||
Serial.println(Load, DEC);
|
||
delay(10);
|
||
}else{
|
||
Serial.println("read Load err");
|
||
delay(500);
|
||
}
|
||
|
||
Move = sc.ReadMove(1);
|
||
if(Move!=-1){
|
||
Serial.print("Servo Move:");
|
||
Serial.println(Move, DEC);
|
||
delay(10);
|
||
}else{
|
||
Serial.println("read Move err");
|
||
delay(500);
|
||
}
|
||
Serial.println();
|
||
}
|